metal clay, art clay, pmc, bronze clay, copper clay, steel clay
FAQ HomeFAQAsk us a QuestionSave your Favorites
Metal Clay Academy Excellence in Art Clay and Precious Metal Clay PMC
Search Advanced Search
Categories
Beginners (49)
Advanced (14)
Glass (2)
Hollow Forms (1)
Patina and Colours (8)
Stones (8)
Technical (30)
Training (2)
Firing (9)
Finishing (10)
Business (3)
Money saving tips (3)
Search
Advanced Search
FAQs
Search our FAQ to find resolutions to common issues.
What is slip?

Slip is a watered down version of metal clay. You can buy slip or paste directly from the suppliers or make your own by adding water to a small lump of clay, filings or dried out clay. Slip can be used to attach two pieces of metal clay together, fill in small cracks or painted onto leaves, flowers, pods etc to make unique designs.

To make slip from scratch, you need a flat, non-porous surface like a piece of glass or plastic, a palette knife or spatular and some water. Take a small piece of metal clay and add a little water - spritzing it with a spray bottle works well.

Work the water into the clay using the palette knife. When the water is absorbed, add some more. Keep adding water and working it in until the clay forms a thick paste. Put it into a clean container - old style film canisters or small glass jam jars work well. You can add more water to the slip and mix with a plastic stirrer or a paint brush until it's the consistency you want.

Whenever you're filing your leather hard pieces, be sure to collect the filings. These can be added to your slip pot and mixed in.

Clay that has dried out can be reconstituted by cutting or grinding into small pieces and mixing with water. If the dried piece is quite large, you might want to make this into a lump of clay again. Otherwise, you can grind or chop it up and add to your slip pot. Make sure you mix in the ground up pieces very well before using in your designs.


Print  Email  Save  Comments  Notify Me  Add to Favorites 
Article ID: 10016 Article Created: 06-11-2008 09:40 AM

How well did this article answer your question? 100% 75% 50% 25% 0%

Most Recently Viewed Articles
How do I get a mirror finish on my work?
There are several techniques that'll help you get a mirror finish without too much hard work. ...
How thick should my clay be?
This depends on what you are making, how deep the texture you're using is, if you're putting texture on the back and the front and also to some extent personal taste. If you're making a pair of small plain earrings, you can roll the clay out to three cards thick. This should make a light pair of earrings that are strong enough to withstand the wear. If you're using deep texture you should go up to five or six cards thick. Deep texture on the back and front of a piece may require your initial rolling to be even thicker. If your piece is going to get lots of wear, like a pendant with a wrap over bail, the bail part should be a little thicker so it can withstand the wear. You will probably know if you've gone too thin when you try to pick the piece up....
Which training course should I choose?
This is a difficult question to answer quickly. There are many training providers throughout the world, many of which have not had any formal training to train others. This doesn’t mean they’re bad teachers though. There are lots of very good teachers who have been working with metal clay for many years and have a wealth of knowledge to pass on to students. ...
Why is newly fired silver metal clay white?
This is the surface of the silver before burnishing. If you could look at it under a microscope you'd see lots of peaks and valleys. This uneven surface doesn't allow the light to reflect so it appears dull white. ...
How can I stop parts of my work getting polished in the tumbler?
Sometimes you might want to have parts of your work with a high shine and other parts with a different finish. This article explores ways of protecting part of your work in the tumble polisher....
How do I roll out a consistently thick slab of clay?
There are several ways of doing this. The simplest and most inexpensive way is to buy some playing cards and use these in equal piles on each side of the lump of clay as you roll it out. For instance, if you want a fairly thin piece of clay for a simple pendant or earrings, you could put a pile of three cards on each side of the clay and use these as a guide for your roller. ...
Can I fire very large Cubic Zirconias or lab created stones in a kiln?
CZ’s and lab created stones should be fine fired in a kiln in PMC3. The creation process involves high heat and pressure so the stones have already been subjected to much more than you will be putting them through in the kiln. If the stone can be fired, it shouldn’t matter what size it is.    ...
What is the process for firing Copper clay with Dichroic glass?
The original copper clay (Copprclay or Hadar's clay) that needs to be fired in carbon can't really be combined with glass in one firing. The glass would pick up the carbon during firing . You could design something that allowed you to connect the glass element after the initial firing, like a traditional prong setting.  There are several reasons why Art Clay Copper Clay or Hadar\'s Quick Fire Copper Clay won\'t work with glass. It needs to be fired at a high temperature so the glass would probably liquify too much. Also the Art Clay Copper works best if you put it in a hot kiln so this would crack the glass due to thermal shock. After firing, it has to be dropped into cold water, another reason why it can\'t be used with glass. Question courtesy of Susan Potter...
How do I laminate PMC sheet?
Cut two identical sized pieces of PMC sheet. Lightly brush water onto one piece and immediately put the other piece on top, being careful to line up the edges. Press down gently to get as many air bubbles out as possible. If you want a completely flat laminated sheet, put something heavy on top of the piece to keep it flat while it dries....
How can I publicise my work?
There are a number of very simple ways to publicise your work and raise your profile as a metal clay artist....