metal clay, art clay, pmc, bronze clay, copper clay, steel clay
FAQ HomeFAQAsk us a QuestionSave your Favorites
Metal Clay Academy Excellence in Art Clay and Precious Metal Clay PMC
Search Advanced Search
Categories
Beginners (49)
Advanced (14)
Glass (2)
Hollow Forms (1)
Patina and Colours (8)
Stones (8)
Technical (30)
Training (2)
Firing (9)
Finishing (10)
Business (3)
Money saving tips (3)
Search
Advanced Search
FAQs
Search our FAQ to find resolutions to common issues.
What copyright rules are applied to rubber stamps?

There is a very useful article here about Angel policies. This link also includes rubber stamp companies who have an Angel policy.


Print  Email  Save  Comments  Notify Me  Delete from Favorites 
Article ID: 10072 Article Created: 10-29-2008 17:36 PM

How well did this article answer your question? 100% 75% 50% 25% 0%

Most Recently Viewed Articles
How do I turn a dried out lump into metal clay I can use?
If it's just dried lumps, break or chop it into the smallest pieces you can, add a little water and mix. Be careful not to over water or you'll get slip. Put it in cling film or Saran Wrap, let sit for a few hours or overnight, knead it through the plastic and add more water. Keep kneading, adding water and/or drying until you get the desired consistency. ...
How can I become a supplier of metal clay?
The distribution of metal clay is controlled by the manufacturers. ...
What is Cubic Zirconia?
A hard and relatively inexpensive synthetic stone, created in laboratories and often cut to resemble a diamond. It is available in a variety of colours and different shapes....
How thick should my clay be?
This depends on what you are making, how deep the texture you're using is, if you're putting texture on the back and the front and also to some extent personal taste. If you're making a pair of small plain earrings, you can roll the clay out to three cards thick. This should make a light pair of earrings that are strong enough to withstand the wear. If you're using deep texture you should go up to five or six cards thick. Deep texture on the back and front of a piece may require your initial rolling to be even thicker. If your piece is going to get lots of wear, like a pendant with a wrap over bail, the bail part should be a little thicker so it can withstand the wear. You will probably know if you've gone too thin when you try to pick the piece up....
How do I roll out a consistently thick slab of clay?
There are several ways of doing this. The simplest and most inexpensive way is to buy some playing cards and use these in equal piles on each side of the lump of clay as you roll it out. For instance, if you want a fairly thin piece of clay for a simple pendant or earrings, you could put a pile of three cards on each side of the clay and use these as a guide for your roller. ...
What natural stones can I fire in place with metal clay?
Being able to push stones into metal clay and fire them in place is a real advantage. Not all natural stones can be fired in place though. Kevin Whitmore from Rio Grande has done extensive testing of stones with metal clay. ...
What is slip?
Slip is a watered down version of metal clay. You can buy slip or paste directly from the suppliers or make your own by adding water to a small lump of clay, filings or dried out clay. Slip can be used to attach two pieces of metal clay together, fill in small cracks or painted onto leaves, flowers, pods etc to make unique designs....
Why is newly fired silver metal clay white?
This is the surface of the silver before burnishing. If you could look at it under a microscope you'd see lots of peaks and valleys. This uneven surface doesn't allow the light to reflect so it appears dull white. ...
What is PMC?
Precious Metal Clay (PMC) consists of microscopic particles of silver or gold suspended in an organic binder to create a pliable material with a consistency similar to modeling clay. PMC can be worked in the fingers and with simple tools to create a vast range of forms and surfaces unobtainable or laborious with traditional metalwork techniques. When it is heated to a high temperature, the binder burns away and the metal particles fuse to form solid metal that can be sanded, soldered, colored and polished like conventional material.    From the Mitsubishi Materials website...
How do I make lavendar or lavender oil paste?
This simple paste is very strong and will stick fired pieces of metal clay together....