metal clay, art clay, pmc, bronze clay, copper clay, steel clay
FAQ HomeFAQAsk us a QuestionSave your Favorites
Metal Clay Academy Excellence in Art Clay and Precious Metal Clay PMC
Search Advanced Search
Categories
Beginners (49)
Advanced (14)
Glass (2)
Hollow Forms (1)
Patina and Colours (8)
Stones (8)
Technical (30)
Training (2)
Firing (9)
Finishing (10)
Business (3)
Money saving tips (3)
Search
Advanced Search
FAQs
Search our FAQ to find resolutions to common issues.
What is the process for firing Copper clay with Dichroic glass?

The original copper clay (Copprclay or Hadar's clay) that needs to be fired in carbon can't really be combined with glass in one firing. The glass would pick up the carbon during firing . You could design something that allowed you to connect the glass element after the initial firing, like a traditional prong setting.
 

There are several reasons why Art Clay Copper Clay or Hadar's Quick Fire Copper Clay won't work with glass. It needs to be fired at a high temperature so the glass would probably liquify too much. Also the Art Clay Copper works best if you put it in a hot kiln so this would crack the glass due to thermal shock. After firing, it has to be dropped into cold water, another reason why it can't be used with glass.


Question courtesy of Susan Potter


Print  Email  Save  Comments  Notify Me  Delete from Favorites 
Article ID: 10085 Article Created: 02-18-2010 14:55 PM

How well did this article answer your question? 100% 75% 50% 25% 0%

Related Articles
Can the Art Clay Silver 650 be fired in a Hot Pot?
Yes...

Most Recently Viewed Articles
What can I do with lots of slip?
There are a number of things you can use slip for apart from the usual things. ...
How can I become a supplier of metal clay?
The distribution of metal clay is controlled by the manufacturers. ...
Can the Art Clay Silver 650 be fired in a Hot Pot?
Yes...
How do I turn a dried out lump into metal clay I can use?
If it's just dried lumps, break or chop it into the smallest pieces you can, add a little water and mix. Be careful not to over water or you'll get slip. Put it in cling film or Saran Wrap, let sit for a few hours or overnight, knead it through the plastic and add more water. Keep kneading, adding water and/or drying until you get the desired consistency. ...
My clay is dry, powdery, flaky and cracking. What can I do?
Spritz or brush the clay with water, wrap it in clingfilm/Saran Wrap and squish the water into the clay. Then leave it for a while. The clay will absorb the water and become usable again. If itís too sticky, leave it open to the air for a short while....
How do I weave paper type metal clay?
There is an excellent tutorial on this on Squidoo written by Margaret Schindel. ...
What are the problems associated with quenching hot metal clay?
If you want to refire, enamel or solder on a piece of metal clay that has been quenched, you may find that moisture has got trapped in the metal. When you heat it again, especially if you heat it fast, the moisture turns to steam and may cause a blister on the surface. You need to dry the piece thoroughly if you have quenched the metal following the initial firing.It is also important to remember that you should not quench a piece which has glass or stones as part of the design. The sudden change in temperature from the firing to the cold water may cause shock and the stone or glass could be damaged or break entirely. Leave your piece to air cool, it should only take a few minutes....
What are the working stages of metal clay?
There are three working stages; lump clay, leather hard or green stage and fired....
Can I enamel a piece of metal clay which Iíve already tumble polished?
If you want to refire, enamel or solder on a piece of metal clay that has been tumble polished, you may find that moisture has got trapped in the metal. When you heat it again, especially if you heat it fast, the moisture turns to steam and may cause a blister on the surface. You need to dry the piece thoroughly if you have quenched the metal following the initial firing....
What can I do with my already fired mistakes?
Sometimes the mistakes can become a wonderful piece of work!...