metal clay, art clay, pmc, bronze clay, copper clay, steel clay
FAQ HomeFAQAsk us a QuestionSave your Favorites
Metal Clay Academy Excellence in Art Clay and Precious Metal Clay PMC
Search Advanced Search
Categories
Beginners (49)
Advanced (14)
Glass (2)
Hollow Forms (1)
Patina and Colours (8)
Stones (8)
Technical (30)
Training (2)
Firing (9)
Finishing (10)
Business (3)
Money saving tips (3)
Search
Advanced Search
FAQs
Search our FAQ to find resolutions to common issues.
How do I laminate PMC sheet?

Cut two identical sized pieces of PMC sheet. Lightly brush water onto one piece and immediately put the other piece on top, being careful to line up the edges. Press down gently to get as many air bubbles out as possible. If you want a completely flat laminated sheet, put something heavy on top of the piece to keep it flat while it dries.


Print  Email  Save  Comments  Notify Me  Add to Favorites 
Article ID: 10034 Article Created: 06-11-2008 11:07 AM

How well did this article answer your question? 100% 75% 50% 25% 0%

Most Recently Viewed Articles
How do I get small clay pieces to stick to a larger piece?
You should always use slip or water to stick two pieces of clay together. Although fresh damp clay may stick together, to be sure, you need to use water or slip between them. ...
Polishing
Tip on how to get a tumble polished finish without buying a tumbler....
Is it better to add Liver of Sulphur patina before or after tumble polishing?
The general advice is to tumble first and add patina afterwards. But read on for more information....
What are the working stages of metal clay?
There are three working stages; lump clay, leather hard or green stage and fired....
Can I enamel a piece of metal clay which I’ve already tumble polished?
If you want to refire, enamel or solder on a piece of metal clay that has been tumble polished, you may find that moisture has got trapped in the metal. When you heat it again, especially if you heat it fast, the moisture turns to steam and may cause a blister on the surface. You need to dry the piece thoroughly if you have quenched the metal following the initial firing....
What is the best way to store syringes so they don't dry out?
There are a variety of ways to store metal clay syringes to ensure they don't dry out. You can store them standing in a small cup of water with the tip or nozzle down in the water. This prevents air from getting into the nozzle and drying the clay. Using cling film or Saran Wrap over the end also stops air getting to the clay and drying it out. A small piece of silver wire inserted into the nozzle can also prevent drying although it needs to be a good fit and it's best to also wrap this in cling film or put it back in the sealed packet it came in. Don't use a steel pin to seal it, steel reacts badly with the clay....
What items react badly with metal clay?
Aluminium reacts badly with metal clay so you should avoid using aluminium foil or work surfaces. Mary Ellin D'Agostino did some experiments with aluminium which you can read by clicking here....
Can I fire very large Cubic Zirconias or lab created stones in a kiln?
CZ’s and lab created stones should be fine fired in a kiln in PMC3. The creation process involves high heat and pressure so the stones have already been subjected to much more than you will be putting them through in the kiln. If the stone can be fired, it shouldn’t matter what size it is.    ...
How thick should my clay be?
This depends on what you are making, how deep the texture you're using is, if you're putting texture on the back and the front and also to some extent personal taste. If you're making a pair of small plain earrings, you can roll the clay out to three cards thick. This should make a light pair of earrings that are strong enough to withstand the wear. If you're using deep texture you should go up to five or six cards thick. Deep texture on the back and front of a piece may require your initial rolling to be even thicker. If your piece is going to get lots of wear, like a pendant with a wrap over bail, the bail part should be a little thicker so it can withstand the wear. You will probably know if you've gone too thin when you try to pick the piece up....
Photopolymer Plates for Enamelling Textures
Pam East uses Photo-polymer plates extensively both for making custom textures and images, and for champleve enameling. She's learned a lot about photo-polymer from Maggie Bergman, Tonya Davidson and many others. She's also developed a few tricks of her own along the way. Here are a few tips that may help....